NEXO FIXX 630 cyanoacrylate adhesives

25.00 - 30.00 / piece

1 Carton (MOQ)

Business Type Manufacturer
Country of Origin India
Type Cyanoacrylate Adhesives
Material Ethyl Cyanoacrylate
Click to view more

Preferred Buyer From

Location Anywhere in India

Product Details

Industrial Use, COMMERCIAL
Colourless To Yellowish Liquid
Ethyl Cyanoacrylate
Adhesive Side
Design Printing
Brand Name
Other Names
18 Month
Specific Gravity @ 25 °C
Refractive Index ( nD²°)
Flash Point
83 °C
Vapour Pressure ( h Pa)
Viscosity (Cp) @ 25 °C
1 - 5
Steel to Steel Curing speed
10 - 30 sec
Stainless steel to Stainless Steel Curing speed
30 - 60 sec
Aluminum to Aluminum Curing speed
5 - 15 sec
Zinc Plate to Zinc Plate Curing speed
30 - 90 sec
ABS to ABS Curing speed
5 - 10 sec
ABS to NRB Curing speed
3 - 5 sec
ABS to WOOD Curing speed
5 - 10 sec
NRB to NRB Curing speed
3 - 5 sec
Wood to Wood Curing speed
50 - 50 sec
Polycarbonate to Polycarbonate Curing speed
20 - 60 sec
Product Code
Payment Terms
Delivery Time
Packaging Details

NEXO FIXX 630 is a general purpose industrial grade Cyanoacrylate adhesive with fast setting ,High flow ability and good penetration characteristics .It has been specially formulated to achieve the strongest possible bond between well - mated, Non porous surface. Such as rubber, metal, plastic. NEXO FIXX 630 is a one component system and does not require the catalyst, Heat or Clamps. When a thin layer of NEXO FIXX 630 is applied between two surfaces come in to contact with atmospheric moisture, a rapid polymerization occurs producing ultimate bond.


Curing Performance

There are many factors that can influence the rate of cure. These include: the type of substrate used, the condition of the surface to be bonded, the smoothness of the surface, the closeness of the surface, the atmospheric conditions like Humidity and Temperature.


Cure speed and Bond Gap (Filling between surfaces)

The rate of cure depends on the Bond Gap (Gap between tow joined surfaces)simply smaller Bang gap faster speed of cure


Direction for Use

 Make sure that the surface to be bonded are clean and dry( Preferable to solvent- wipe plastic,glass,rubber and acid treat to Metals

 Dispense a Drop / Drops to one surface only. Apply only enough to leave a thin film after compression.

 Press Parts Together and hold firmly for few seconds. Good Contact is essential. An Adequate bond develop in less than one minute ( Maximum strength achieved in 24 to 48 Hours)

 Wipe off the excess of adhesive from top of container and recap NEXO FIXX 630 if left uncapped may deteriorate by contamination from moisture in the air.

 Because NEXO FIXX 630 condenses by polymerization sometime whitening will occur on the surface of the container or the bonded material. Should this happen. Wipe surface with acetone.


7) Handling and Storage

Storage Keep Product in unopened container in cool and dry location.

Best when stored at 2 to 8 °C Temp less than 2 °C can adversely affect product properties. Do not freez.Keep container closed to air tight till ready for use.

Handling Material removed from Containers may contaminate during use. Do not pour back any material removed from container again to full / partial container misuse of product will void all warrantees.


8) Precautions and safety Note

 Use with proper ventilation, Avoid contact with skin and eyes.

 In case of skin contact rinse with warm water or dissolve gradually with solvent like acetone or nitro methane, do not remove forcefully or pull, rub on hardly, allow it to release slowly after some time.

 If adhesive went in to eye, Keep eye open and rinse thoroughly. Seek medical attention immediately

 Keep well out of rich of children’s

 Keep adhesive in cool, Dry place 20 to 25°C( 68 to 77°F), for long time storage 2 to 35°C is preferred

Yes! I am interested

Looking for "NEXO FIXX 630 cyanoacrylate adhesives" ?


Explore More Products

Raise your Query

Hi! Simply click below and type your query.

Our experts will reply you very soon.

WhatsApp Us